Control protocol ---------------- A running tinc daemon is listening on a UNIX socket. Other programs can connect to this socket and send commands to control or query the running daemon. The messages sent over the socket are simple lines of text. The daemon creates a PID file and a socket in `/var/run` normally (if `./configure` has been run with `--localstatedir=/var`). They are called: /var/run/tinc..pid /var/run/tinc..socket These are only readable by the same user that started the tinc daemon. If the `--user` option was used, but tinc was started by root, then these files will still only be readable by root. Note, the control protocol is not stable yet, and may change at any point until version 1.1.0 is released. Authentication -------------- When connecting to the UNIX socket, the first line sent by the tinc daemon looks like: 0 17.0 The third word, 17.0, is the major.minor version of the protocol used by tinc. The first sent to the tinc daemon must be of this form: 0 ^ 0 Where must be replaced by the cookie value found in the PID file created by the tinc daemon. This is the second word of the first line in `/var/run/tinc.netname.pid`. Note, the `^` must still be put in front of the actual cookie value. If the cookie is accepted, the tinc daemon will respond with a line that looks like: 4 0 Message format -------------- Subsequent messages are always in this format: 18 Where is a numeric code that identifies the type of request, and is a space-separated list of parameters. The available request types can be found in the `enum request_type` in `control_common.h`. The tinc daemon will normally respond with: 18 Where is the same as sent in the request, and is a numeric result, where 0 normally indicates success, and non-zero values indicate an error. However, some requests will have other results, see below. Requests -------- - `REQ_STOP`: stop the running tinc daemon. - `REQ_DUMP_NODES`: dump information about all known nodes. See below for the result format. - `REQ_DUMP_EDGES`: dump information about all known edges. See below for the result format. - `REQ_DUMP_SUBNET`: dump information about all known subnets. See below for the result format. - `REQ_DUMP_CONNECTIONS`: dump information about all meta-connections this tinc daemon has. See below for the result format. - `REQ_PURGE`: purge information about unreachable nodes. - `REQ_SET_DEBUG `: set the debug level for the default log output to . - `REQ_RETRY`: retry any pending outgoing connections immediately. - `REQ_RELOAD`: instructs the running tinc daemon to reload its configuration files. - `REQ_DISCONNECT `: close any meta-connection with node . Returns 0 if success, -1 for invalid requests, and -2 if there was no meta-connection to this node. - `REQ_DUMP_TRAFFIC`: dump network traffic statistics. See below for the result format. - `REQ_PCAP `: start sending a packet capture stream to the control socket, with up to bytes per packet. - `REQ_LOG `: start sending log output at level to the control socket. Dump formats ------------ Dumps result in multiple lines, that all start with: 18 The last line does not contain any parameters, and indicates the end of the dump. The following sections list the parameters provided for each dump type: ## REQ_DUMP_NODES 1. node name 2. node ID (in hexadecimal format) 3. currently active address 4. the word "port" 5. currently active port 6. cipher ID (OpenSSL NID) 7. digest ID (OpenSSL NID) 8. digest length (in bytes) 9. compression level 10. bitfield of enabled options (hexadecimal, see OPTION_* in connection.h) 11. bitfield of current status (hexadecimal, see node_status_t in node.h) 12. nexthop 13. via 14. distance (in hops) 15. current path MTU 16. minimum discovered MTU 17. upper bound for MTU 18. time of last state change (in seconds since 1970-01-01 00:00 UT) ## REQ_DUMP_EDGES 1. node name from 2. node name to 3. address of the "to" node 4. the word "port" 5. port of the "to" node 6. local address of the "from" node 7. the word "port" 8: local port of the "from" node 9: bitfield of enabled options (hexadecimal, see OPTION_* in connection.h) 10: edge weight ## REQ_DUMP_SUBNETS 1. subnet 2. owner name, or `(broadcast)` for broadcast subnets. ## REQ_DUMP_CONNECTIONS 1. node name, or `` for control connections, or `` if no name is known yet 2. address of the node 3. the word "port" 4. port of the node 5. bitfield of enabled options (hexadecimal, see OPTION_* in connection.h) 6. socket fd 7. bitfield of current status (hexadecimal, see connection_status_t in connection.h) ## REQ_DUMP_TRAFFIC 1. node name 2. number of packets received from node 3. number of bytes received from node 4. number of packets sent to node 5. number of bytes sent to node