Support :: in IPv6 Subnets.

[tinc] / doc / tinc.texi

diff --git a/doc/tinc.texi b/doc/tinc.texi
index 9e8929b..d0fb70d 100644 (file)
--- a/doc/tinc.texi
+++ b/doc/tinc.texi
@@ -794,12 +794,14 @@ tinc won't try to connect to other daemons at all,
 and will instead just listen for incoming connections.
 
 @cindex DecrementTTL
-@item DecrementTTL = <yes | no> (yes)
+@item DecrementTTL = <yes | no> (no) [experimental]
 When enabled, tinc will decrement the Time To Live field in IPv4 packets, or the Hop Limit field in IPv6 packets,
 before forwarding a received packet to the virtual network device or to another node,
 and will drop packets that have a TTL value of zero,
 in which case it will send an ICMP Time Exceeded packet back.
 
+Do not use this option if you use switch mode and want to use IPv6.
+
 @cindex Device
 @item Device = <@var{device}> (@file{/dev/tap0}, @file{/dev/net/tun} or other depending on platform)
 The virtual network device to use.
@@ -1160,12 +1162,11 @@ Multiple subnet lines can be specified for each daemon.
 Subnets can either be single MAC, IPv4 or IPv6 addresses,
 in which case a subnet consisting of only that single address is assumed,
 or they can be a IPv4 or IPv6 network address with a prefixlength.
-Shorthand notations are not supported.
 For example, IPv4 subnets must be in a form like 192.168.1.0/24,
 where 192.168.1.0 is the network address and 24 is the number of bits set in the netmask.
 Note that subnets like 192.168.1.1/24 are invalid!
 Read a networking HOWTO/FAQ/guide if you don't understand this.
-IPv6 subnets are notated like fec0:0:0:1:0:0:0:0/64.
+IPv6 subnets are notated like fec0:0:0:1::/64.
 MAC addresses are notated like 0:1a:2b:3c:4d:5e.
 
 @cindex CIDR notation
@@ -2402,7 +2403,6 @@ For IPv4 addresses:
 @tab @code{netsh interface ip set address} @var{interface} @code{static} @var{address} @var{netmask}
 @end multitable
 
-
 For IPv6 addresses:
 
 @multitable {Darwin (MacOS/X)} {ifconfig route add -bla network address netmask netmask prefixlength interface}
@@ -2424,6 +2424,22 @@ For IPv6 addresses:
 @tab @code{netsh interface ipv6 add address} @var{interface} @code{static} @var{address}/@var{prefixlength}
 @end multitable
 
+On some platforms, when running tinc in switch mode, the VPN interface must be set to tap mode with an ifconfig command:
+
+@multitable {Darwin (MacOS/X)} {ifconfig route add -bla network address netmask netmask prefixlength interface}
+@item OpenBSD
+@tab @code{ifconfig} @var{interface} @code{link0}
+@end multitable
+
+On Linux, it is possible to create a persistent tun/tap interface which will
+continue to exist even if tinc quit, although this is normally not required.
+It can be useful to set up a tun/tap interface owned by a non-root user, so
+tinc can be started without needing any root privileges at all.
+
+@multitable {Darwin (MacOS/X)} {ifconfig route add -bla network address netmask netmask prefixlength interface}
+@item Linux
+@tab @code{ip tuntap add dev} @var{interface} @code{mode} @var{tun|tap} @code{user} @var{username}
+@end multitable
 
 @c ==================================================================
 @node    Routes