Fix broken links, use https:// where available.

[wiki] / examples / proxy-arp.mdwn

diff --git a/examples/proxy-arp.mdwn b/examples/proxy-arp.mdwn
index 70cb092..39335d0 100644 (file)
--- a/examples/proxy-arp.mdwn
+++ b/examples/proxy-arp.mdwn
@@ -7,7 +7,7 @@ IP address inside the local LAN's subnet), one can set up a bridge at the local
 node, as described in the [[bridging example|examples/bridging]].  However,
 setting up a bridge is rather complex, and if one only needs unicast IP traffic
 to work, and broadcast or non-IP traffic is not a requirement, one can use the
-[proxy ARP](http://en.wikipedia.org/wiki/Proxy_ARP) features of the operating
+[proxy ARP](https://en.wikipedia.org/wiki/Proxy_ARP) features of the operating
 system instead.
 
 Since we only use unicast IP traffic, proxy ARP works with both router and
@@ -22,46 +22,46 @@ The network setup is as follows:
 
 ### Configuration of tinc at the office
 
->     host# cat /etc/tinc/vpn/tinc.conf
->     Name = office
->     #Optional:
->     #Mode = switch
->     
->     host# cat /etc/tinc/vpn/tinc-up
->     #!/bin/sh
->     
->     ifconfig $INTERFACE 192.168.1.2 netmask 255.255.255.255
->     route add 192.168.1.123 dev $INTERFACE
->     echo 1 >/proc/sys/net/ipv4/conf/eth0/proxy_arp
->     echo 1 >/proc/sys/net/ipv4/conf/$INTERFACE/proxy_arp
->     
->     host# ls /etc/tinc/vpn/hosts
->     office  roadwarrior  ...
->     
->     host# cat /etc/tinc/vpn/hosts/office
->     Address = 123.234.123.42
->     Subnet = 192.168.1.0/24
->     -----BEGIN RSA PUBLIC KEY-----
->     ...
->     -----END RSA PUBLIC KEY-----
->     
->     host# cat /etc/tinc/vpn/hosts/roadwarrior
->     Subnet = 192.168.1.123
->     -----BEGIN RSA PUBLIC KEY-----
->     ...
->     -----END RSA PUBLIC KEY-----
+       host# cat /etc/tinc/vpn/tinc.conf
+       Name = office
+       #Optional:
+       #Mode = switch
+       
+       host# cat /etc/tinc/vpn/tinc-up
+       #!/bin/sh
+       
+       ifconfig $INTERFACE 192.168.1.2 netmask 255.255.255.255
+       route add 192.168.1.123 dev $INTERFACE
+       echo 1 >/proc/sys/net/ipv4/conf/eth0/proxy_arp
+       echo 1 >/proc/sys/net/ipv4/conf/$INTERFACE/proxy_arp
+       
+       host# ls /etc/tinc/vpn/hosts
+       office  roadwarrior  ...
+       
+       host# cat /etc/tinc/vpn/hosts/office
+       Address = 123.234.123.42
+       Subnet = 192.168.1.0/24
+       -----BEGIN RSA PUBLIC KEY-----
+       ...
+       -----END RSA PUBLIC KEY-----
+       
+       host# cat /etc/tinc/vpn/hosts/roadwarrior
+       Subnet = 192.168.1.123
+       -----BEGIN RSA PUBLIC KEY-----
+       ...
+       -----END RSA PUBLIC KEY-----
 
 ### Configuration of tinc at the road warrior
 
->     host# cat /etc/tinc/vpn/tinc.conf
->     Name = roadwarrior
->     #Optional:
->     #Mode = switch
->     
->     host# cat /etc/tinc/vpn/tinc-up
->     #!/bin/sh
->     
->     ifconfig $INTERFACE 192.168.1.123 netmask 255.255.255.0
+       host# cat /etc/tinc/vpn/tinc.conf
+       Name = roadwarrior
+       #Optional:
+       #Mode = switch
+       
+       host# cat /etc/tinc/vpn/tinc-up
+       #!/bin/sh
+       
+       ifconfig $INTERFACE 192.168.1.123 netmask 255.255.255.0
 
 The host config files are, of course, identical to those on the office node.
 
@@ -72,7 +72,7 @@ to the roadwarrior's address hardcoded.  To have tinc automatically add the
 necessary routes, remove the `route add` command from the `tinc-up` script, and
 instead add this `subnet-up` script:
 
->     host# cat /etc/tinc/vpn/subnet-up
->     #!/bin/sh
->     [ "$NAME" = "$NODE" ] && exit 0
->     ip route replace $SUBNET dev $INTERFACE
+       host# cat /etc/tinc/vpn/subnet-up
+       #!/bin/sh
+       [ "$NAME" = "$NODE" ] && exit 0
+       ip route replace $SUBNET dev $INTERFACE